Elite indicators :) - page 193

William Snyder
9496
William Snyder  
AndreusTSD:
_forex-tsd.com/attachments/manual-trading-systems-indicators/87475d1270782331t-elite-indicators-dtoscwithjrsx.gif Hello! What indicator pain bars in red and green on this chart?

Try here https://www.mql5.com/en/forum/general post # 1912

and the other files needed for Ssa bars to work are here https://www.mql5.com/en/forum/general post#1801!

AndreusTSD
11
AndreusTSD  

thanks!

give me advice please, what most intresting indicator I can see in Elite Section and Advance Elite Section?

I'm new here, your advice to me would be very helpful

killerpips
18
killerpips  

d

mrtools:
Try here https://www.mql5.com/en/forum/general post # 1912 and the other files needed for Ssa bars to work are here https://www.mql5.com/en/forum/general post#1801!

Please do you have sth i can read to know how to use the TTM Ssa Bars ??

Or some explanations . . . How is it reacculating? When is it doing it?

When should i consider the color as final? Brief how to use it, i have put it, but somes difficulties to use it.

Thank you for your explanations . . .

Mladen Rakic
151209
Mladen Rakic  

SSA (singular spectrum analysis) in general (which is the basis of SSA bars) recalculates last Lagbars.

It is doing it all the time (depending on price changes, of course. Most obvious situations are when there are reversals, when you will notice rather big changes invalues) since it is trying to fit the value the best it can to price changes

regards

Mladen

killerpips:
Please do you have sth i can read to know how to use the TTM Ssa Bars ??

Or some explanations . . . How is it reacculating? When is it doing it?

When should i consider the color as final? Brief how to use it, i have put it, but somes difficulties to use it.

Thank you for your explanations . . .
Mladen Rakic
151209
Mladen Rakic  
Files:
hbear
111
hbear  

VMA/Ehlers Zone

Mladen

I found both VMA and EhlersNonlinearFilter and especially VMA Zones great indicators. VMA zones draws a band based on high and low of the VMA.

Could you make VMA zones and also zone version of the Ehlers filter?

The NT code for the VMA zone is like this:

Upper.Set(VMA(High, Length, Volatility)[0]);

Lower.Set(VMA(Low, Length, Volatility)[0]);

I attached the indicator in MQL.

Thanks,

Heiko

Mladen Rakic
151209
Mladen Rakic  

Heiko,

First the Vidya zone

Added one thing : a middle line. You can turn it of (or any of the 3 Vidya values) by setting the appropriate CmoPeriod (Chande momentum period) to less than 1.
PS: any of the 3 Vidyas is fully controllable (so they do not have to be same periods or smoothing periods) That way it can even be "misused" to do something like this (in a single indicator) :
____________________________

PS: be advised that this version has an error in it. I have left it here as a comparison to the correct one (correct one can be downloaded from this post : https://www.mql5.com/en/forum/general )

regards

Mladen

altoronto
318
altoronto  

SSL Bar 3 - no repaint

Hi Mladen, can you fix attached indicator for repainting issue?

As always, thank you in advance.

hbear
111
hbear  
mladen:
Heiko,

First the Vidya zone

Added one thing : a middle line. You can turn it of (or any of the 3 Vidya values) by setting the appropriate CmoPeriod (Chande momentum period) to less than 1.
PS: any of the 3 Vidyas is fully controllable (so they do not have to be same periods or smoothing periods) That way it can even be "misused" to do something like this (in a single indicator) :
regards Mladen

Quick as the wind....

I am not sure though whether your version is equal as the lines are crossing each other in certain movements.

In the NT version it seems this is not possible.

I attached an example. May it depends on the settings..I am just checking.

Files:
vmazones.jpg 96 kb
Mladen Rakic
151209
Mladen Rakic  

Heiko,

___________________________

This is not the original post I posted as an answer to your question.

First I thought that it is impossible what you say, and answered thus. Sorry man if you read that answer. You were and are right. I apologize

___________________________

It took me some hair pulling and comparing all the bloody Vidyas I have found on the whole net and all they behaved the same way : in some cases Vidya of high and Vidya of low indeed crossed (and they crossed as a trooper not just marginally) Until I realized what is the error : Chande momentum oscillator must be calculated exclusively on Closeand not the chosen price. That means that all the Vidyas calculated have the same CMO value and hence, they all are smoothed the same way at same bars. Once I made the changes (and avoided different volatility for different prices), all came to order (thanks God, otherwise I would go crazy how can it happen)

So here is : simplified in order to do just the zone using same CmoPeriod and SmoothPeriod for all chosen values that you would like to be displayed.
So, folks, please download this version : this one is the correct one (no crosses of high low in this one ). I am leaving the original one too (posted a couple of posts ago, so you all can see what is and where it is changed and compare and witness those high-low crosses) So as a conclusion : in Vidya, whatever price is used, volatility must be calculated on close in order to leave different Vidyas compatible and comparable to each other

___________________________

Now I can sleep. Good nigh to all

regards

Mladen

heikobaer:
Quick as the wind....

I am not sure though whether your version is equal as the lines are crossing each other in certain movements.

In the NT version it seems this is not possible.

I attached an example. May it depends on the settings..I am just checking.

updated version posted here: https://www.mql5.com/en/forum/general

Files: