# Signal Lotsize

371

Hi Guy, I would like to ask about if i've subscribed signal with balance 1000\$ and copy order with 0.01 lot
If I deposit another 1000\$, Will my existing order increase lot size?

Thanks
Moderator
106113

You can calculate by yourself using the formulas below:

Sergey Golubev, 2017.02.02 07:45

How to Select a Deal Volume?
The question of how exactly the Subscriber's deposit will participate in trading via Signals service is one of the most critical ones. When solving this issue, we followed the already mentioned principle - providing maximum protection for each participant. As a result, we can offer a secure solution for Subscribers.

The question of how exactly the Subscriber's deposit will participate in trading via Signals service is one of the most critical ones. When solving this issue, we followed the already mentioned principle - providing maximum protection for each participant. As a result, we can offer a secure solution for Subscribers.

When enabling signals in the terminal and subscribing to one of them, Subscribers should select what part of the deposit is to be used when following the signals. There was an alternative solution of setting the ratio between Subscriber's and Provider's position volumes. But such a system could not guarantee the security of the Subscriber's deposit. For example, suppose that Provider's deposit is 30 000\$, while Subscriber's one is 10 000\$ and the ratio of 1:1 has been selected. In that case, the Signals Provider may just wait out temporary drawdown having a large volume order, while the Subscriber may lose all the funds with all his or her positions closed by Stop Out. The situation may get even worse if the Provider's balance suddenly changes (top up or withdraw), while previously specified volumes ratio remains intact.

To avoid such cases, we have decided to implement the system of percentage-based allocation of the part of a deposit, which is to be used in trading via the Signals service. This system is quite complicated as it considers deposit currencies, their conversion and leverages.

Let's consider a specific example of using the volumes management system:

1. Provider: balance 15 000 USD, leverage 1:100
2. Subscriber1: balance 40 000 EUR, leverage 1:200, deposit load percentage 50%
3. Subscriber2: balance 5 000 EUR, leverage 1:50, deposit load percentage 35%
4. EURUSD exchange rate = 1.2700

Calculation of Provider's and Subscriber's position volumes ratio:

1. Balances ratio considering specified part of the deposit in percentage terms:
Subscriber1: (40 000 * 0,5) / 15 000 = 1,3333 (133.33%)
Subscriber2: (5 000 * 0,35) / 15 000 = 0,1166 (11.66%)
2. After considering the leverages:
Subscriber1: the leverage of Subscriber1 (1:200) is greater than Provider's one (1:100), thus correction on leverages is not performed
Subscriber2: 0,1166 * (50 / 100) = 0,0583 (5.83%)
3. After considering currency rates of the deposits at the moment of calculation:
Subscriber1: 1,3333 * 1,2700 = 1,6933 (169.33%)
Subscriber2: 0,0583 * 1,2700 = 0,0741 (7.41%)
4. Total percentage value after the rounding (performed using a multistep algorithm):
Subscriber1: 160% or 1.6 ratio
Subscriber2: 7% or 0.07 ratio

Thus under the given conditions, Provider's deal with volume of 1 lot will be copied:

- to Subscriber1 account in amount of 160% -  volume of 1.6 lots

- to Subscriber2 account in amount of 7% -  volume of 0.07 lots

Be careful not to confuse the percentage value of the used part of the deposit and the actual ratio of position volumes. The trading terminal allows setting the part of the deposit in percentage value. This value is used to calculate the ratio of position volumes. This data is always fixed in the log and is shown in the following way:

Subscriber1:

2012.11.12 13:33:23 Signal '1277190': percentage for volume conversion selected according to the ratio of balances and leverages, new value 160%

2012.11.12 13:27:55 Signal '1277190': signal provider has balance 15 000.00 USD, leverage 1:100; subscriber has balance 40 000.00 EUR, leverage 1:200

2012.11.12 13:27:54 Signal '1277190': money management: use 50% of deposit, equity limit: 0.00 EUR, deviation/slippage: 1.0 spreads

Subscriber2:

2012.11.12 13:33:23 Signal '1277191': percentage for volume conversion selected according to the ratio of balances and leverages, new value 7%

2012.11.12 13:27:55 Signal '1277191': signal provider has balance 15 000.00 USD, leverage 1:50; subscriber has balance 5 000.00 EUR, leverage 1:50

2012.11.12 13:27:54 Signal '1277191': money management: use 35% of deposit, equity limit: 0.00 EUR, deviation/slippage: 1.0 spreads

---------------

Signal Subscriber Lot Size Question

Sergey Golubev, 2017.02.02 07:42

Besides, you can use Calculator of the Signals (to calculate everything 'automatically' based on any pre-selected signal for example).

Moderator
106113

Increasing lot size

Sergey Golubev, 2016.11.29 01:03

On Provider's account all trades are performed with volume of 0.1 lots. I want to copy these trades with larger volume, for example 0.3 lots. Can I raise the volume somehow?
All volumes are calculated automatically. Subscriber can copy trades with volume larger than on Provider's account only in one case - if Subscriber's account balance reserved for signals copying is greater than Provider's account balance (Subscriber_Balance * Load > Provider_Balance).

Moderator
6600

taechita:
Hi Guy, I would like to ask about if i've subscribed signal with balance 1000\$ and copy order with 0.01 lot
If I deposit another 1000\$, Will my existing order increase lot size?

Thanks

No, because the lot size is rounded down and never up, so you will need \$1000 more in order to double your lot size to 0.02.