Maya MT4
- 专家
- Manpreet Singh
- 版本: 1.513
- 更新: 19 四月 2024
- 激活: 5
MAYA is the advanced trading system which was tested for long on different market conditions with heavy load tests. Based on TRIANGULAR ARBITRAGE SYSTEM and entry rules based on our custom indicator which is backed with mean reversion concept along with few other algorithm this products fits itself into the current market conditions and act accordingly.
If you want to backtest then download only MT5 version for testing
MT5 Version :- https://www.mql5.com/en/market/product/99108
Supported currency pairs: AUDCAD, AUDNZD, NZDCAD
Recommended timeframe: M1 & M15. Default settings are for M15 chart, for M1 chart keep "Signal Coefficient = 2" and keep rest of the settings unchanged
MULTI CURRENCY EA CANNOT BE BACKTESTED ON MT4 SO YOU CAN TEST THE WORKING BY FOLLOWING OUR MT4 SIGNAL BELOW
- https://www.mql5.com/en/signals/1900652
Key Features
- Easy Setup: You just need to drag the EA on AUDCAD chart.
- It can trade multiple currencies together.
- 3 Risk modes available
- Easy to use
- Much cheaper than similar products available on market place
- Weekdays Filters
Installation Guide
- The EA must be attached to ONLY one M1 chart, AUDCAD is recommended (If you want to use higher TF then contact personally for settings)
- If your broker uses a suffix (e.g. AUDCAD.a,AUDCAD#) you should update symbols with suffix which are separated by commas.
- Use recommended pairs only. You don't need .set files, all settings are stored internally in the EA
- Add AUDCAD in Pair_1 field, AUDNZD in Pair_2 and NZDCAD in Pair_3 field
Requirements
- You may use any broker having spread lesser than 1.5, ECN Broker Preferred.
- Continuous VPS connection required.
- EA was tested on high loads on account minimum as $400 1:500, But we recommend minimum $1000 with leverage 1:500 on default settings.
Trade Controls
- Initial Lot is 0.01 for each mode for an account size of $1000 for agressive mode, $700 for intermediate and $200 for conservative
- Lot Multiply Factor is 2 by defaults, this is useful in agressive and intermediate mode, this setting will multiply the lot size of previous opened trade to open next trade with an increased lot size for each pair individually.
- Lot Multiply After Trades is 2 by default, this setting helps you control the multiplication of lot after certain number of trades. Let's take an example on default settings, if initial lot is 0.01 it will start multiplying the trades after opening two 0.01 lot size trades, 1st & 2nd positions will be 0.01 each, 3rd and 4th positions will be 0.02 each, 5th and 6th positions will be 0.04 each and so on when multiply factor is 2. You can increase and decrease this number.
- Profit is set to 1 as default for 1 for M1 pair, any change to this settings is only effective if we increase the time frame.
- Pips Gap is the gap between each trade that will be open in following grid system applicable to Agressive and Intermediate modes only.
- Signal Coefficient is 2 for M1 chart, if we increase the time frame then this settings need to change.
Risk Controls
- You need not to change any setting until you change time frame.
- Agressive mode is default mode, in this all pairs works as per their own behaviour.
- Intermediate mode is drawdown will be lower than Agreesive and each pair behaves according to its counter parts.
- Conservative mode is the safest mode and you can trade with an account as low as $200, but profit is also very low on this mode. In this mode grid is off.
Instruments Controls
- Market Instruments need to be separated by comma and add suffix your broker using if any (Like "#", "_",",").
- Pair 1, Pair 2 and Pair 3 fields are left blank due to validation purpose on mql5. But you need to add those fields before use including suffix if your broker use.
- Pair_1 - AUDCAD
- Pair_2 - AUDNZD
- Pair_3 - NZDCAD
- Do not change the sequence of the symbols
Running Controls
- Time Filter to adjust the start and stop time of EA during the day.
- Weekdays Filter to control the working of EA on particular days of week.
- Magic - Will happen after you start using this EA :)
