All orders
Rules
Job finished
Specification
It is important that the basic structure of the EA remains the same.
Please note this is used for crypto and $, not in pips.
Also note the trailing buy is based on % from MA, not % change in price.
The Trailing Buy works like a Trailing Stop with a Step, but is implemented before the Open trade is placed.
EDITS NEEDED:
PART I:
1. ADD Trailing Buy. Edit Manageopen so that When Bid hits input x% above MA, the EA needs to start a trailing buy with an input step y% and the input place order z%
Example
if initial x=5% above MA and y=2% and z=1% then:
For Short/Sell Open:
When bid reaches x (5%) above the MA the trailing buy goes into effect.
If Bid rises and hits the Initial x% above ma + step y (2%) above ma (7% above MA) before Bid drops and hits place order z% (x 5%- z 1%= 4% above MA) then step y and place order increases z rise the step value y 2% above ma.
For Long/Buy Open: Opposite
1a. Add ON/OFF input to print on chart when x% above MA is hit and mark on chart y and z. if Bid hits step Y% above MA then print and mark on the chart the new y% and z % Note: this is to be drawn as a smma + step y% line and an smma place order z% line on the chart that follows the bid price.
2. ADD input ON/OFF for a multiplier %.
2a. ADD inputs a and b for multiplier % for y and z.
If multiplier is turned on, then the second time the bid hits X% above MA + step Y% above MA, Step y% and/or Place order z% times multiplier % from a and/or b.
3. VERIFY in manageopen before order is placed that when Bid hits input y place order % that the bid is still x-y% above Exit MA indicator values.
4. ADD inputs for opening order to be placed by lot, % of balance, or % of margin.
5. ADD inputs for simple, exponential, and weighted to the current MA. Currently it is set to Smoothed MA only.
6. ADD input for ON/OFF breakeven and ON/OFF Trailing Stop Loss ON/OFF by % of price.
6a. ADD inputs for break even % and Trailing Stop Loss %.
7. ADD input for Long/short, long only, short only
8. ADD Market or Pending Limit order Option
9. Add Pending Limit Order Offset by % of Bid Price from MA. Pending limit orders are placed towards the MA.
11. Add Option ON/OFF time limit to cancel Pending Limit Order
12 Add Input for Time to cancel Pending Limit Order in minutes. Should also accept for example .5 minutes as 30 seconds.
13. Input option ON/OFF for time delay. After trade is closed delay X amount of time before next trade is placed. Add input options for seconds, minutes, hours.
Part II
14. ADD a way to store for example the X amount (say 20) high % bid rises above MA over the last X amount of time (say 24 hours) and X amount of low % bid falls below MA. (Must be Bid. Not on Close)
So for example it would store 20 for both Bid high and low % from MA (5%, 4.2%, 3%, 10%, etc.)
As time passes it would drop those that are past X amount of time (For example if amount of time is set to 24 hours, Values over 24 hours old would be dropped and replaced by values from within the last X 24 hours.
(Upon startup values initial values could be created from current period bar highs/lows % from MA. As time passes values would be replaced by data from Bid above/below % from MA
14a. ADD these input options to work with 114. (stored % from MA values)
Input option Use Stored % Values ON/OFF
Input for amount of Values above MA % to be stored (example 50)
Input for amount of Values below MA % to be stored (example 50)
Input for amount of X amount of hours for Above MA % to be stored (example, 24 for the last 24 hours stores the 50 largest value% above MA and the 50 largest value% below MA)
Input option ON/OFF to place a mark on the chart for each value.
Input option ON/OFF to show those values listed on the chart on the left side (Both Above % values and Below % values listed separately).
Input options to list by date starting with the most recent or by highest for the values to be displayed either by date order or from highest to lowest values.
Input for number of stored values to use in the calculation. (Input above may store 50 values. This input could be set to only use only the highest 30)
Input for number of values to dropped from the amount from storage above (30) to be used before calculation method is applied. for example 50 stored, 30 values used in calculation, with input here of 1 would drop the highest and lowest values from both above MA% and below MA%. (use values 2-29) 2 would drop the 2 highest and 2 lowest values from above MA% and the 2 highest and 2 lowest (use values 3 -28) etc.
Input options for the calculation method of stored MA% values (high, low, simple, median, typical, exponential, smoothed, and weighted)
Input option ON/OFF to show on left of chart both above MA % value and below MA % value (Show high, low, median, typical, exponential, smoothed, and weighted values)
If input option Use Stored % Values is on, then use the (typical, median, whatever is selected) value as the input value for the initial x% above MA (See 1 above)
Can give more detailed explanation if needed.