100:1 leverage

New comment
 
My signal is on a 100:1 leverage account. I can't see how it could work on 500:1 leverage (without scaling the performance back) which most of the signals seem to run on. What do people think? Thanks
 
Neil Michael Riddell:
My signal is on a 100:1 leverage account. I can't see how it could work on 500:1 leverage (without scaling the performance back) which most of the signals seem to run on. What do people think? Thanks

Those with larger leverage will not have any impact and those with smaller will have a smaller copying ratio.

 

Risk depends on your initial stop loss, lot size, and the value of the symbol. It does not depend on margin and leverage. No SL means you have infinite risk (on leveraged symbols). Never risk more than a small percentage of your trading funds, certainly less than 2% per trade, 6% total.

  1. You place the stop where it needs to be — where the reason for the trade is no longer valid. E.g. trading a support bounce, the stop goes below the support.

  2. AccountBalance * percent/100 = RISK = OrderLots * (|OrderOpenPrice - OrderStopLoss| * DeltaPerLot + CommissionPerLot) (Note OOP-OSL includes the spread, and DeltaPerLot is usually around $10/PIP, but it takes account of the exchange rates of the pair vs. your account currency.)

  3. Do NOT use TickValue by itself - DeltaPerLot and verify that MODE_TICKVALUE is returning a value in your deposit currency, as promised by the documentation, or whether it is returning a value in the instrument's base currency.
              MODE_TICKVALUE is not reliable on non-fx instruments with many brokers - MQL4 programming forum (2017)
              Is there an universal solution for Tick value? - Currency Pairs - General - MQL5 programming forum (2018)
              Lot value calculation off by a factor of 100 - MQL5 programming forum (2019)

  4. You must normalize lots properly and check against min and max.

  5. You must also check Free Margin to avoid stop out

  6. For MT5, see 'Money Fixed Risk' - MQL5 Code Base (2017)

Most pairs are worth about $10 per PIP. A $5 risk with a (very small) 5 PIP SL is $5/$10/5 or 0.1 Lots maximum.

 
Eleni Anna Branou #:

Those with larger leverage will not have any impact and those with smaller will have a smaller copying ratio.

thanks Eleni

 
William Roeder #:

Risk depends on your initial stop loss, lot size, and the value of the symbol. It does not depend on margin and leverage. No SL means you have infinite risk (on leveraged symbols). Never risk more than a small percentage of your trading funds, certainly less than 2% per trade, 6% total.

  1. You place the stop where it needs to be — where the reason for the trade is no longer valid. E.g. trading a support bounce, the stop goes below the support.

  2. AccountBalance * percent/100 = RISK = OrderLots * (|OrderOpenPrice - OrderStopLoss| * DeltaPerLot + CommissionPerLot) (Note OOP-OSL includes the spread, and DeltaPerLot is usually around $10/PIP, but it takes account of the exchange rates of the pair vs. your account currency.)

  3. Do NOT use TickValue by itself - DeltaPerLot and verify that MODE_TICKVALUE is returning a value in your deposit currency, as promised by the documentation, or whether it is returning a value in the instrument's base currency.
              MODE_TICKVALUE is not reliable on non-fx instruments with many brokers - MQL4 programming forum (2017)
              Is there an universal solution for Tick value? - Currency Pairs - General - MQL5 programming forum (2018)
              Lot value calculation off by a factor of 100 - MQL5 programming forum (2019)

  4. You must normalize lots properly and check against min and max.

  5. You must also check Free Margin to avoid stop out

  6. For MT5, see 'Money Fixed Risk' - MQL5 Code Base (2017)

Most pairs are worth about $10 per PIP. A $5 risk with a (very small) 5 PIP SL is $5/$10/5 or 0.1 Lots maximum.

thanks William

New comment
Reason: