Need help with Back Tester
>
"stopped because of Stop Out" is wirtten in the journal.
Seems that you get a Margin Call...
Why would I get a margin call if I was making a profit?
well i suggest you start reading what a margin call is and how the margin used and free margin is calculated... note that you would require some free margin to open a position...
rortiz77:
Why would I get a margin call if I was making a profit?
The two are independent. Some free margin to open a position is only half the problem. As the market move against the position(s), free margin drops. Once it reaches zero - margin call. If you max out your margin and the market drops by one point, margin call.Why would I get a margin call if I was making a profit?
You must prevent margin call by reducing lot size for the last open order.
perLotPerPoint = PointValuePerLot(); total.risk = 0; oo.lots = 0; // _> multiple open. for(int pos = OrdersTotal()-1; pos >= 0 ; pos--) if ( OrderSelect(pos, SELECT_BY_POS) // Only my orders w/ && OrderMagicNumber() == Magic.Number // my magic number && OrderSymbol() == Symbol() ){ // and period and symbol oo.lots += OrderLots(); perPoint = OrderLots()*perLotPerPoint, eRisk = DIR*(OrderOpenPrice()-OrderStopLoss())*perPoint; if (eRisk > 0) total.risk += eRisk; // Total balance reduction. ... double LotSize(double risk){ ... compute size ... double minLot = MarketInfo(Symbol(), MODE_MINLOT), LotStep = MarketInfo(Symbol(), MODE_LOTSTEP), perLotPerPoint = PointValuePerLot(), maxLossPerLot = risk * perLotPerPoint, size = at.risk / maxLossPerLot; // Must still round to LotStep. /*---- Compute lot size based on account balance and MM mode*/} /* The broker doesn't care about the at.risk/account balance. They care * about margin. Margin used=lots used*marginPerLot and that must be less * than free margin available. Using the lesser of size vs * AccountFreeMargin / MODE_MARGINREQUIRED should have been sufficient, but * the tester was generating error 134 even when marginFree should have been * OK. So I also use AccountFreeMarginCheck < 0 which agrees with the * tester. Reported at https://www.mql5.com/en/forum/128506 * * Second problem, after opening the new order, if free margin then drops to * zero we get a margin call. In the tester, the test stops with: "EA: * stopped because of Stop Out" So I make sure that the free margin * after is larger then the equity risk so I never get a margin call. */ EA.status = "SL>AE"; // Assume size < minLot while (true){ // Adjust for broker, test for margin, combine with TEF... size = MathFloor(size/LotStep)*LotStep; if (size < minLot){ Print("LotSize(SL=", DoubleToStr(risk/pips2dbl, Digits.pips), " pips)=", size, "<", minLot, " ", EA.status, ", MMM=", Money.Management.F0M1G2, "@", Money.Management.Multiplier); at.risk=0; return(0); } at.risk = size * maxLossPerLot; // Export for Comment if (at.risk+total.risk > maxRisk){ size *= (maxRisk-total.risk)/at.risk; EA.status = "MaxRisk"; continue; } double AFMC = AccountFreeMarginCheck(Symbol(), op.code, size), eRisk = risk*(oo.lots+size)*perLotPerPoint; if (AFMC <= eRisk){ size *= 0.95; EA.status = "Free Margin"; continue; } // Prevent margin call if new trade goes against us. return(size); // We're good to go. } /*NOTREACHED*/ } // LotSize double PointValuePerLot() { // Value in account currency of a Point of Symbol. /* In tester I had a sale: open=1.35883 close=1.35736 (0.00147) * gain$=97.32/6.62 lots/147 points=$0.10/point or $1.00/pip. * IBFX demo/mini EURUSD TICKVALUE=0.1 MAXLOT=50 LOTSIZE=10,000 * IBFX demo/standard EURUSD TICKVALUE=1.0 MAXLOT=50 LOTSIZE=100,000 * $1.00/point or $10.00/pip. * * https://www.mql5.com/en/forum/127584 CB: MODE_TICKSIZE will usually return the * same value as MODE_POINT (or Point for the current symbol), however, an * example of where to use MODE_TICKSIZE would be as part of a ratio with * MODE_TICKVALUE when performing money management calculations which need * to take account of the pair and the account currency. The reason I use * this ratio is that although TV and TS may constantly be returned as * something like 7.00 and 0.00001 respectively, I've seen this * (intermittently) change to 14.00 and 0.00002 respectively (just example * tick values to illustrate). */ return( MarketInfo(Symbol(), MODE_TICKVALUE) / MarketInfo(Symbol(), MODE_TICKSIZE) ); // Not Point. }
Can't understand why my back tester just stops all of the sudden??? I took a quick video of my setup...
please take a look and let me know if you see anything wrong.
Thanks!